Renesas Electronics uPD720200 USB 3.0 Controller driver for Windows 7 - Renesas Electronics uPD720200 USB 3.0 Controller

Renesas Electronics uPD720200 USB 3.0 Controller Updater 3.0.3.4

Renesas Electronics uPD720200 USB 3.0 Controller driver from Renesas for Windows XP, Wind

Renesas Electronics uPD720200 USB 3.0 Controller driver from Renesas for Windows XP, Windows Vista, Windows XP 64 bit, Windows Vista 64 bit, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit

Publisher review for Renesas Electronics uPD720200 USB 3.0 Controller Updater 3.0.3.4:

Before install Renesas Electronics uPD720200 USB 3.0 Controller Updater 3.0.3.4you should set a system restore point, to make sure you can rollback to your original driver in case you accidentally install another driver or select the driver for another version of the operating system.

Also, do not forget to check with our site as often as possible for new version of Renesas Electronics uPD720200 USB 3.0 Controller . We recommend to always use most recent version of a driver.

"F303408FWUP1.EXE" updates uPD720200 FW from verion 3.0.2.8 or older
to 3.0.3.4. If the FW version is 3.0.3.4 or later, it does not update.
Note1 : F303408FWUP1.EXE is uPD720200 CS sample or Mass Product whose revision ID of PCI Configuration Register is 3h.
Note2 : If uPD720200 is not detected on the target PC, F303408FWUP1.EXE does not start to update.
Note3 : If multiple uPD720200s are detected on the PC, F303408FWUP1.EXE does not start to update. 
Note4 : F303408FWUP1.EXE updates FW regardless of SSID and SVID in the serial ROM.
(If you want to limit the update target to the device with specific SSID
and SVID, you can generate the update file with "FW Updater Generator".)
Note5 : Users must restart or shoutdown after updating the FW. Usage1. Disconnect all USB devices connected with the USB3.0 ports.
2. Execute "F303408FWUP1.EXE".
3. Show the License Agreement. If you accept all the terms of the
preceding License Agreement, please select "I accept".
4. Show the precaustions. Please check all items.
5. Press "Update" button.
6. After updating, let you restart the computer.
7. Confirm FW Version.
On the Start menu, click All Programs, RENESAS Electronics,
USB3.0 Host Controller Driver, and then USB3.0 Hsot Controller Utility.
8. Show USB3.0 Host Controller Information. If "Firmware Version" is 3034,
you succeed in updating FW.
The following problems are fixed.1. Fixed the USB3.0 Host Controller in D3hot didn't send the PME Message 
when it received any wakeup events.
2. The following issue is fixed by ver 2.1.19.0 of RENESAS USB 3.0 Host
Controller Driver, but there was a possibility that this could still
occur in Windows 8:
[RENSAS USB 3.0 Host Controler Driver ver 2.1.19.0's history]
1. USB3.0 devices aren't detected when users perform the below steps.
a) Turn on a PC.
b) Enter sleep (S3 state) without connecting USB3.0 devices.
c) Connect USB3.0 devices to a USB3.0 port during S3 state.
d) USB 3.0 HDD isn't detected.
The USB3.0 devices aren't detected after the PC resumes from S3 state.
With Windows 7 or earlier, this issue only occurs with driver Ver.2.1.16.0.
3. There is a possibility that the USB 3.0 Host controller cannot notify 
the xHCI Driver when the Host controller receives the following contiguous
Device Notification Transaction Packets: Function Wake Notification,
Latency Tolerance Message (LTM) Device Notification, Bus Interval Adjustment Message Device Notification. We have never seen this problem on a real system.
4. Improved the interoperability of UAS devices in Windows 8.

Operating system:
Windows XP, Windows Vista, Windows XP 64 bit, Windows Vista 64 bit, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit